Kirby Morgan 77

Submitted by nick on 27 September 2011 - 5:40am

Where to Buy

Body:

KM77 Top Tab

Manual KM 77

This is your operations and maintenance manual. It is a writable USB flash drive which enables you to add or subtract the manual PDF sections as they are updated or when you purchase new Kirby Morgan products.

Part #
100-085
Logbook w/ pen

Part #
125-001
Helmet/Mask Bag

Measurements: 16’’ length x 12’’ width x 16’’ height. Made of high quality, tough black nylon, encasing a lightweight, white polyethylene foam that features low water absorption and is fairly rigid (good impact strength). The two grommeted ventilation holes seen in the photo are on both sides of the bag. A large elastic topped pocket is on each side, for holding tool kits, checklists, logbooks, spares, etc. (There are no inside pockets). The bag handles are 1” wide straps of black polyester webbing. The bag closes up with two, large YKK zippers. We do not recommend the 500-901 helmet bag as a shipping container or packaging for your Kirby Morgan life support equipment!

Part #
500-901

km77_tabber

Manual KM 77

This is your operations and maintenance manual. It is a writable USB flash drive which enables you to add or subtract the manual PDF sections as they are updated or when you purchase new Kirby Morgan products.

Part #
100-085
Logbook w/ pen

Part #
125-001
Over Pressure Relief Valve

The Kirby Morgan^® Overpressure Relief Valve is factory adjusted to vent any time the pressure in the low pressure hose connecting the bailout bottle to your emergency valve exceeds 200 P.S.I. It is installed in any of the low pressure ports in the first stage regulator.

Part #
200-017
SuperFlow First Stage, No Hose

Part #
305-161
Helmet/Mask Bag

Measurements: 16’’ length x 12’’ width x 16’’ height. Made of high quality, tough black nylon, encasing a lightweight, white polyethylene foam that features low water absorption and is fairly rigid (good impact strength). The two grommeted ventilation holes seen in the photo are on both sides of the bag. A large elastic topped pocket is on each side, for holding tool kits, checklists, logbooks, spares, etc. (There are no inside pockets). The bag handles are 1” wide straps of black polyester webbing. The bag closes up with two, large YKK zippers. We do not recommend the 500-901 helmet bag as a shipping container or packaging for your Kirby Morgan life support equipment!

Part #
500-901
Restrictor Adapter

The 555-210 Restrictor Adapter should be used when an inflation hose is attached to the side block when drysuit diving. The main purpose of the Restrictor Adapter is to limit gas flow in the event the hose ruptures or is severed, and to ensure the loss of supply would not be great enough to significantly affect the diver’s breathing at moderate to heavy work rates. It also helps prevent filling the dry suit too rapidly.

NOTE: O-ring 310-003 is required to install the Restrictor Adaptor onto the side block.

Part #
555-210

Accessory Kits

Chin Cushion

Part# 510-683
Head Cushion Assembly

The fit of the head cushion is critical to both comfort and safety. The head cushion should be adjusted so that it assists in the proper seal of the oral nasal mask to the face. The head cushion is one out of a three part system. The Earphone holes are no longer present in the side pieces, but may be cut if the user prefers. The material is laser cut to prevent the edges from fraying or unraveling and has a handy loop attached to the liner for hanging and drying.

Part# 510-754
525-112 Pull Pin Sleeve

This sleeve, created for the 505-110 sealed pull pins (found on all models of KM helmets except the SL 17B & MK 21), is an option to help prevent the knob of the pull pin from snagging or catching on objects or protrusions.

Part# 525-112
Front Standoff Kit

Part# 525-116
Conversion Kit, 350 Regulator for KM 77

Part# 525-385
Welding Shield Assembly

The Welding Shield covers the entire viewport area of your helmet or mask, and accepts a standard 4 x 5 inch weld glass.This welding shield will retrofit to all KMB BandMasks® and SuperLite® helmets using the same mounting holes as the original, smaller, weld lens assembly.

Part# 525-400
Weld Lens Assembly

The Welding Lens Assembly will fit all SuperLite^® Kirby Morgan^® Helmets and BandMasks^®. The port retainers are supplied with two plug screws which are designed to protect the two threaded holes on the port retainer which are provided for the welding lens assembly.

There are three densities of lens available:

Part # 525-405 Lens, Light (#5)

Part # 525-406 Lens, Medium (#10)

Part # 525-407 Lens, Dark (#12)

This assembly is designed to provide visual protection only!

Part# 525-403
Communications Module for Posts Kit

Part# 525-420
Communications Module for MWP Kit

Part# 525-430
Replacement Foam Kit for 510-754 Head Cushion

Part# 525-746
Conversion Kit, 455 Regulator for KM 77

Part# 525-769
REX 47/77 Regulator Assembly Kit

Part# 525-774