|
|
|
For SuperLite 17 (shown) & SuperLite 27, 17B, KM 37 Helmets and KMB-18 & KMB-28 Band Masks "B" side block only.
The Hot Water Shroud, Part #525-100 , can be used whenever diving operations are conducted on mixed gas, or when diving in cold water. The shroud helps warm the diver's incoming air, thereby lessening diver's heat loss.
|
|
|
|
|
 |
KMDSI offers a large Welding Shield, Part # 525-400, which covers the entire viewport area of your helmet or mask, and accepts a standard 4 x 5 inch weld glass.This welding shield will retrofit to all KMB BandMasks and SuperLite helmets using the same mounting holes as the original, smaller, weld lens assembly.
The 4 x 5 lenses (weld glass) are sold separately:
PART # 525-411 Medium (#10)
PART # 525-412 Dark (#12)
|
|
|
|
|
|
|
This Welding Lens Assembly, Part # 525-403, will fit all SuperLite Kirby Morgan Helmets and Band Masks. The port retainers are supplied with two plug screws which are designed to protect the two threaded holes on the port retainer which are provided for the welding lens assembly.
There are three densities of lens available:
PART # 525-405___lens, Light (#5)
PART # 525-406___lens, Medium (#10)
PART # 525-407___lens, Dark (#12)
This assembly is designed to provide visual protection only!
|
|
|
|
|
|
|
|
To protect your SuperLiteHelmet or BandMask, the KMDSI helmet/mask carrying bag, Part # 500-901 should be used when transporting or storing your helmet between jobs. The DSI bag is made from extra heavy duty, black, ripstop nylon. The bottom of the bag is padded for additional protection. Grommeted drain holes allow the bag to breath. The bag is also equipped with large carrying straps and side pockets.
|
|
|
|
|
|
|
|
The Oral Nasal masks used in our helmets and full face masks help lower the carbon dioxide levels while improving speech communications. Our Silicone Oral Nasal Mask is made of a superior silicone material which is hypo-allergenic and has a longer work life than standard latex. The new silicone oral nasal, Part# 510-690, replaces the older 510-540 & 510-547 Latex Oral Nasals.
|
|
 Part # 510-569
Latex Small Oral Nasal for SL-27 |
 Part # 510-669 Latex Small Oral Nasal for SL-17, SL-17C, KMB-18, & KMB-28
|
|
|
|
|
  |
The Quad Valve™ makes use of the existing main exhaust body on the Kirby Morgan® 17K helmet, as well as model KM 37, and the SuperLite-17A/B. (A separate version will be available for the SuperLite®-27.)The system will not work on the SuperLite®-17C, or any model of Kirby Morgan Band Mask®. The Band Mask® will only accept the Tri-Valve® Exhaust at this time. The 17C is not designed to accept the Tri-Valve™ or Quad Valve™.
WARNING: The Quad Valve™ is recommended for diving in biologically contaminated water only. The chemical compatibility of this exhaust system has NOT been tested at this time, so no recommendations are made regarding environments polluted with hazardous chemicals. Prior to diving in contaminated water, the diver must be properly trained and equipped, and a proper dive plan, including provisions for decontamination following the dive, must be formulated. Failure to follow these precautions could result in serious injury or death |
|
|
|
|
 |
The Tool Kit, Part #525-620, is available for setting up and adjusting the regulator on your SuperLite-17, SuperLite-27 helmet KMB-18 & KMB-28 BandMask for maximum performance. |
|
|
|
|
 |
This kit, Part # 525-130, is designed to allow the alteration of the trim, or balance of the SuperLite 17/MK 21 diving helmet. It adds 2 lbs. to the overall weight of the helmet. The weight replaces the exhaust body cover with no obstruction of the exhaust port. The weight is designed to blend in to the contours of the helmet with nothing that would hang up or become snagged while working.
THIS WEIGHT IS NOT FOR USE WITH THE DOUBLE EXHAUST!
|
|
|
|
|
|
 |
The chin weight of the SL-27 has been removed and a side weight added. This brings improved balance to the helmet as well as providing an accessory ( lights, cameras, etc.) mounting area. There are four 10-24 threaded holes with screws on the weight for this purpose. As of 8/15/95, these parts are "standard" on all SuperLite-27 helmets.
For retrofitting older helmets, order
Weight Kit Part # 525-220.
|
|
|
|
|
 |
This catch allows the diver a quicker, easier removal of the helmet. As of January of 1996, this part is standard on all SL-17K, SL-27 and SL-17C helmets.
For Retro fit upgrades order
Part # 525-106 for the SL-27
Part # 525-135 for the SL-17C
|
|
|
|
|
 |
This catch, Part # 505-010, standard on all SL-17 Helmets, allows the yoke to be dropped without breaking the seal of the neck clamp. The hole pattern in the Pull Pin Latch Catch Body is identical to the Push Pin Latch Catch Body and mounts on the yoke the same. However the screws provided with the Pull Pin Latch Catch are longer than the original mount screws. The Push Pin Latch Catch screws should not be used to mount the Pull Pin Latch Catch Body.
The earlier style Push Pin Latch Catch DSI # 505-015 is now obsolete
|
|
|
|
|
 |
Beginning in January, 2004, all SuperLite 17A/B and MK-21 Helmets will come equipped with a new Yoke Strap, Part # 505-134, Yoke Strap Guide, Part # 505-138 and a new helmet mounted chin strap, Part # 505-130 |
 |
These new parts are retrofitable on all older SuperLite 17A/B & MK-21 Helmets and are available in a kit, Part # 525-234. |
|
|
| |
Top of Page
|
 |
Accessory Mounting Brackets for KM 37, KM 47, SL17K
| PART# |
DESCRIPTION |
| 530-040 |
Screw |
| 540-130 |
Bracket |
| 540-132 |
Bracket |
|
|
|
|
|
 |
Part # 525-752 SuperLite 17B,and KM 37 Kit
Part # 525-755 SL-27 Kit
|
|
|
|
 |
